ReadMe for Landis+Gyr MAP190 Package Release: 5.9.14 Package Date: 23.10.2013 1. Description -------------- Landis+Gyr MAP190 is designed to create articles and orders for devices of the E850, E650, E550 meter series as well as communication units E65C and E35C. 2. Most recent changes, enhancements and bug fixes -------------------------------------------------- Changes to release 5.9.14 (2013-10-23) - Operating Systems: Windows 8 now supported. - Setup: Main version number (5.9) added to all program links in the Windows start menu to allow an unambiguous identification of the program in case of multiple installations. - Setup: Update component (dMAPUPdate) removed from the setup since its functionality is now fully integrated into the MAP190 application. - ZxQ200: Voltage phase fail threshold corrected in case of ZCQ devices. - ZxQ200: Starting load of 0.1% for devices with a nominal current of 0.3 A and 120% Imax introduced. - ZxQ200: Network diagnostic list can be edited. - ZxD300/400: Maximum value of demand monitors now limited to 65535 kW/var/VA or 65535 MW/var/VA (depending on primary data adaptation) - ZxD300/400: Signed measured quantities removed as a source for demand registers. - ZxD300/400: Designation 'Alarm input' removed from control input signal TI-mb, TI-KA and TI-KB (firmware B31 only). - ZxD300/400: New SMS format for DC 450 is limited to devices with integrated interface only. - ZxD300/400: Fraud detection signals in control table and as source of arrows and outputs have been limited (firmware B31 only). - ZxD300/400: When switching to a device description of type 'base meter with module interface the communication unit is reset to eliminate potential rule violations in the hidden part. - ZxD300/400: Scaler of primary power with unit 'Mega' now correct (firmware B32 only). - ZxD300/400: New extension board '0470' and '0477' now supported (firmware B32 only). - ZxD300/400: ID string of 'end' entry in display lists and menus not checked anymore. - ZxG300/400: ID string of 'end' entry in display lists and menus not checked anymore. - ZxG300/400: First entry of the day in load profile 2 now stored correctly. - CU-P4x: Support of firmware D72. Changes to release 5.8.14 (2013-07-30) - ZxD300/400 Parameterisation of all phase measured quantities |+A|+|-A|, |+A|-|-A|, |+R|+|-R|, |+R|-|-R| corrected (firmware B31 and B32 only). - ZxD300/400: Iron losses now stored with decimal places. - ZxG300/400: Iron losses now stored with decimal places. Changes to release 5.8.12 (2013-05-03) - ZxQ200: Enhancement of primary voltage up to 1200 kV. - ZxD300/400: Fraud detection signals now available in the control table and as control source for outputs (firmware B31 only). - ZxD300/400: Unsupported alarm signals removed from control source of arrows and outputs (firmware B31 only). - ZxD300/400: 800 V variant removed (firmware B31 only). - ZxD300/400: Primary instantaneous values not available anymore for direct connected meters. - ZxD300/400: Terminal cover type not shown anymore if a device without terminal cover has been selected. - ZxD300/400: Editing of ID strings in display lists now possible in all cases. - ZxD300/400: All security system settings are retained when the firmware is switched from B31 to B32. - ZxD300/400: The selection of quadrants and phases of the energy registers now permanently restricted if the power factor has been activated in the configuration. - ZxG300/400: Support of firmware P07. - ZxG300/400: Loading of default settings of external 3rd party modems changed. - ZxG300/400: Battery voltage swells adapted. - ZxG300/400: Terminal cover type not shown anymore if a device without terminal cover has been selected. - ZxG300/400: Various checks of the settings of the electrical interfaces removed. - ZxG300/400: Unused access levels are not printed anymore. - ZxD series: Designation of signal 'TI-KB' corrected again. - AD-xP/xG: Unit and scaler of the instantaneous active power register now included in the MAP120 export file (*.prd) (firmware T25 and T05). Changes to release 5.7.32 (2013-03-06) - ZxD300/400: Dlms register resolution of energy register 25 to 32 now set to the same value as for all other energy registers (firmware B31 and B32 only). Changes to release 5.7.30 (2013-01-08) - ZxD300/400: Strong DC field detection and terminal cover removal signals enabled for arrows and outputs (firmware B31 and B32 only). - CU: Wrong security group assignment of the time master object fixed (firmware D50, D51 and D60). Changes to release 5.7.28 (2012-12-11) - ZxD300/400: In CU only device descriptions the 'end' entry is not checked anymore (no rule violation anymore). - ZxD300/400: Security group of the light control feature adapted to better support remote control (firmware B32 only). Changes to release 5.7.26 (2012-12-10) - Database: Database selection window enlarged and sorting possibilities added. - ZxD300/400: Support of firmware B32. - ZxD300/400: Additional check of the 'end' entry in the display and readout lists. - ZxD300/400: Maximum demand register source selection reduced to measured quantities ME1 to ME8 and ME11/ME12 (firmware B31 and up). - ZxD300/400: 2 new PISTA elements added for the start current. - ZxD300/400: Missing access rights for level E can be manually added. - ZxG300/400: No check of primary data anymore in case of direct connected meters. - ZxG300/400: The reverse stop per phase setting in the measured quantities selection remains stored correctly. - ZxG300/400: Dependencies between calculation method of apparent energy and THD corrected. - ZxG300/400: 2 new PISTA elements added for the start current. - CU-P4x: Changes to be in line with most recent D71 firmware. Changes to release 5.6.04 (2012-08-22) - ZxG300/400: Control signals for under current monitoring are now set correctly (firmware P05 and P06 only). Changes to release 5.6.02 (2012-05-22) - Tool: New high resolution tool icon. - Database: Support of the Oracle 11 ODBC database driver. - Database: The old Microsoft JET database engine to access a MS Access database is not supported anymore. It has been replaced by the Microsoft Access Database Engine (ACE). - CU-P4x: Support of firmware D71 for series production. Changes to release 5.4.26 (2012-04-03) - CU-P4x: Support of firmware D71.6 for pilot series. Changes to release 5.4.24 (2012-03-23) - all devices: Embossing of all seals changed back to 'LG' ('SM' removed). - ZxD300/400: New measured quantity: Active energy with reverse stop per phase (firmware B31 only). - ZxD300/400: Additional security attribute 'service menu' for access level 7 now available. - ZxD300/400: Support of hardware detection of terminal cover removal (firmware B31 only). - ZxD300/400: Support of new terminal covers:'60mm for Gx-Source, transparent' and 'CU-ADP Adapter'. - ZxD300/400: In=40 A removed for ZxD300 MID meters. - ZxD300/400: Printout of control table option in configuration corrected. - ZxG300/400: Support of new terminal covers:'60mm for Gx-Source, transparent' and 'CU-ADP Adapter'. - ZxG300/400: Access level 2 now supported over second communication channel. - CU-P4x: Support of firmware D71 for pilot series. Changes to release 5.4.14 (2012-01-18) - CU: M2x and Zx added again in configuration, Px removed. - CU-P4x: Now also available together with ZxQ meters. Changes to release 5.4.12 (2011-12-23) - ZxG300/400: Support of firmware R06. - ZxG300/400: Support of 2 new extensions boards '0600' and '2400' (firmware P06 and R06 only). - ZxG300/400: Support of p1 interface (firmware P06 only). - ZxG300/400: Packaging enhanced to offer the same possibilities as ZxD300/400. - ZxD300/400: Support of new extension board '326x' (firmware B31 only). - ZxD300/400: Support of ZPD317/417 meters for pilot series (firmware B31 only). - ZxD300/400: Preliminary support of additional rules and modifications related to the summation of external pulse inputs (firmware B31 only). - CU-P4x: Preliminary support of firmware D71 for pilot series. Changes to release 5.3.06 (2011-09-16) - all devices: Drop down list containing DST begin and end enhanced by 04:00. - AD-xP/xG: Support of firmware T05 and T25. - AD-xP/xG: Logistics information related to SIM card only shown for AD-xG devices. - AD-xP/xG: Energy values profile and billing values profile renamed to load profile 1 and load profile 2. - ZxD300/400: Erroneous meter constant now shown right after opening the tree. - ZxD300/400: Gregorian calendar is the new default value after changing the firmware version. - ZxQ200: Maximum current not changed anymore after activation of primary current. - ZxQ200: Designation of several OBIS codes corrected: 1-b:0.6.0 Nominal voltage, 1-b:0.6.1 Nominal current, 1-0:x.126 = all harmonics of measured quantity x. - CU: Assembly instructions now available for CU only orders. Changes to release 5.2.20 (2011-08-04) - ZxG300/400: Total registers of line and transformer losses enabled (OBIS codes 83.8.19 and 83.8.20). Changes to release 5.2.18 (2011-04-08) - ZxD300/400: Additional check of an activated stored values profile to contain at least one entry. - ZxQ200: Number of energy register extended to 16 in c.4 configuration. Changes to release 5.2.16 (2011-03-31) - ZxG300/400: Phase angle calculation corrected (firmware P05 and P06 only). Changes to release 5.2.12 (2011-03-03) - AD-xP/xG: M-Bus device list extended by Landis+Gyr T550 and T230. - ZxG300/400: Support of firmware P06. - ZxD300/400: Register resolution of energy total register 19 corrected (firmware B31 only). - ZxD300/400: Security system settings modified to allow a proper enabling and disabling of the THD registers (firmware B31 only). - ZxD300/400: Extended power quality only can be selected in the configuration if the instantaneous values are selected as well. - ZxQ200: The grid and the installation diagnostic display lists are now shown (content can't be modified). Changes to release 5.1.38 (2011-02-09) - ZxD300/400: Enabling and disabling of external pulse inputs doesn't require security level 4 anymore (firmware B31 only). Changes to release 5.1.36 (2011-01-24) - ZxD300/400: Strong DC field detection enabled again (firmware B31 only). Changes to release 5.1.34 (2011-01-18) - ZxD300/400: Load profile control enabled again (firmware B30 only). Changes to release 5.1.32 (2011-01-12) - ZxD300/400: Security system adapted to allow again the change of the number of stored values in display lists (firmware B31 only). Changes to release 5.1.30 (2010-12-16) - AD-xP/xG: Wrongly disabled multi utility registers and profiles generate an error. - AD-xG: Range of number of network login repetitions extended. - ZxG300/400: Final support of firmware P05 (R05). - ZxG300/400: Extension of trigger sources for alerts (firmware P05 only). - ZxG300/400: In devices without load profile no profile is triggered anymore (firmware P05 only). - ZxD300/400: Conversion between transformer operated and direct connected meters possible again. - ZxD300/400: Designation of events 93 and 89 harmonised. - ZxD300/400: In devices without load profile no profile is triggered anymore (firmware B30 and B31 only). - ZxD300/400: CS signal assignments in control input for event 12 and 13 corrected (firmware B31 only). - ZxQ200: The sign of the instantaneous active and reactive power must be equal. - ZxQ200: The network diagnostic display list is now shown (content can't be modified). - ZxQ200: Additional restrictions on starting load of active energy. - CU-Q22: Assignment of measured quantities (order) adapted to IEC standard. Changes to release 5.1.24 (2010-11-12) - ZxD300/400: Additional check of the meter constants when opening a device description. Changes to release 5.1.22 (2010-11-02) - ZxD300/400: Final support of firmware B31 (various corrections). Changes to release 5.1.18 (2010-10-18) - ZxG300/400: Quadrant selection for measured quantities fixed. Changes to release 5.1.16 (2010-10-06) - OBIS codes: All OBIS codes are now shown in numeric format only (as defined in the standard) instead of partly using characters. Affected values: 'C'=96, 'F'=97, 'L='98' and 'P'=99. This now allows a correct referencing to the standard. Please note that the ID strings in the display and readout lists haven't changed. - Country list: Now available on Windows 7 PC's without a modem driver installed. - Physical HDLC device address: Empty address now prohibited. - ZxG300/400: Device configuration without load profile active supported again. - ZxG300/400: Visible errors modified (firmware P05 and P50 only). - ZxG300/400: Event triggers modified (firmware P05 and P50 only). - ZxG300/400: Billing period average power factor only selectable for display lists and profiles if energy register 15 and 16 are configured accordingly. - ZxG300/400: Signed values for active and reactive power supported (firmware P05 and P50 only). - ZxD300/400: Support of firmware B31. - ZxD300/400: Check of meter constant now based on maximal current instead of nominal current. - ZxD300/400: Number of pages in the event log configuration can't be set to 0 anymore. - ZxD300/400: Captured objects selection of load profile 1 and stored values profile restricted again. This only applies to devices with load profile 2 enabled. - ZxD300/400: Printout of load profile 2 removed from configuration of devices not supporting 2 load profiles. - ZxQ200: If the capture period of a profile is set to the subinterval length, the average register values captured in the load profile are adapted accordingly (firmware H04 only). - ZxQ200: For every output signal of the control table it can be selected individually, if it is activated immediately or at the end of the integration period. - ZxQ200: Signed values for active and reactive power supported (firmware H03 and H04 only). - ZxQ200: Active starting load of 0.03% supported for all devices. - AD-xP/xG: M-Bus value selection not restricted anymore by medium in the M-Bus device configuration. Changes to release 5.0.22 (2010-07-12) - ZxQ200: Capture period length of load profile 1 can be modified again for devices without demand measurement. Changes to release 5.0.20 (2010-06-14) - AD-xG: Alert trigger sources are now set correctly. Changes to release 5.0.18 - Operating systems: Windows 7 now supported. - Setup: Program now located in a dedicated Landis+Gyr program group in the start menu by default. - Visual identity: New splash screen, new about box, small modifications in menus (Tools and Help). - CU-Q22: Support of firmware D91. - CU-Gx/Px: Handling of PIN code modified (has no effect on parameterisation). - CU-G3x/P3x: Support of BGS3 modem chipset. - AD-xG: Network ID can be parameterised using a constant + the manufacturer serial number. - AD-xP/xG: Display of memory capacity in days corrected in profiles (has no effect on parameterisation). - AD-xP/xG: Rate indexes in OBIS codes of energy registers are automatically corrected for new orders if necessary. - ZxG300/400: Support of firmware P05 (R05) for pilot series production. - ZxG300/400: Alert triggers corrected (power quality events are now working). - ZxG300/400: Printout of extension boards corrected. - ZxG300/400: Right sealing screw right now selectable (firmware R0x only). - ZxG300/400: Average instantaneous values instead of current values are now captured in the load profile. - ZxD300/400: Folder 20948 'Instantaneous Values Monitoring' renamed to 'Power Quality'. - ZxD300/400: CT and VT ratio remain constant if nominal voltage or current is changed. - ZxD300/400: ZxD400 meters supporting a maximal current of 15 or 20 A cancelled for firmware B24 and B30. - ZxQ200: Support of firmware H04. - ZxQ200: Average power factor can be added to profile 2. - ZxQ200: In case of sliding demand the capture period of the profile is now selectable (subinterval length or capture period). - ZxQ200: Capture period 2 not shown twice anymore (firmware H03 only). - ZxQ200: No minimal pulse value shown if losses are selected for an pulse output. - ZxQ200: IEC readout list enhanced with additional registers, mainly instantaneous values. Changes to release 4.5.26 - ZxG300/400: Unit of demand registers 5,7 and 8 corrected. Changes to release 4.5.22 - ZxD300/400: Impulse value of pulse output corrected for devices with a nominal current of 0.3 A. - ZxD300/400: Burden is now correctly broken for devices with a nominal current of 0.3 A. Changes to release 4.5.18 - AD-xP/xG: Capture period of energy values profile enhanced to 1 day. - ZxQ200: Frequency monitoring events enabled in event log trigger sources. Changes to release 4.5.16 - Setup: Check for updates directly possible from MAP190 if an Internet connection is available. New item 'Check for Updates' in help menu. - AD-xP/xG: Full support of firmware T24 for pilot series production. - AD-xP/xG: Definition of several M-Bus channels using the same M-Bus address now possible. - AD-xP/xG: Predefined device list for simpler handling of M-Bus devices now available (firmware T04,T24 and up). - AD-xP/xG: Configuration: Channel number in OBIS code of energy registers selectable between 0 and 1 (firmware T04,T24 and up) - ZxG300/400: Introduction of several new current and voltage variants. - ZxG300/400: Introduction of a new variant supporting maximum load calculation (firmware P04 and up). - ZxG300/400: Replacement of '5||1 A' meter by '1 A (600%)'. - ZxD300/400: Strong DC field detection added as trigger source for alert (series 3 and up). - ZxD300/400: Introduction of a new variant of ZxD400 supporting a maximum current of 15 and 20 A (firmware B24 and up). - ZxD300/400: Introduction of a new variant of ZxD402 supporting a nominal current of 0.3 A (series 3 and up). - ZxD300/400: Replacement of 5||1 A meter by a '1 A (1000%)' variant with a flexible maximum current. - ZxD300/400: Various adaptations of 800V peak variant. - ZxD300/400: Customer specific designation of terminal T0-8 possible again in case of fraud detection activated (series 3 and up). - ZxQ200: Support of firmware H04 for pilot series production. - ZxQ200: Correction of current and voltage thresholds in case of three wire connection. Changes to release 4.4.38 - ZxD300/400: The control input used for strong DC field detection remains active as a source for the control table if a data set is opened (firmware B30 only). Changes to release 4.4.36 - all devices: Passive TOU now also printed in case of undefined activation date. - all devices: Printout of maximum load profile size in days corrected. - CU-Gx: Printout of additional SIM card information on the face plate added. - CU-Mx/Gx: Text for modem time window generalised. - AD-xP/xG: Support of firmware T04 (final) and T24 (prerelease only). - AD-xP/xG: Minimum sliding window size of maximum demand supervision set to 5 minutes. - ZxD100AR: Printout of 85 A maximum current now supported. - ZxG300/400: -A now also supported for active energy only meters. - ZxG300/400: ER15 und ER16 can be edited again. - ZxD300/400: Support of series 3 devices (firmware B30). - ZxD300/400: Introduction of 12mm lead seals. - ZxD300/400: Additional rules for S0 inputs added. - ZxQ200: Apparent energy now selectable independent of demand configuration. - ZxQ200: Cumulative maximum demand register now selectable in display lists. - ZxQ200: Unit of energy register ER27 corrected to Wh. - ZxQ200: Modifications of the number of load profile entries now indicated as in ZxD300/400. - ZxQ200: Naming of event 43 corrected to 'end of integration period due to clock change'. - ZxQ200: Integration period inscription can be entered in all cases again. - ZxQ200: Update of configuration after changing the firmware version. - ZxQ200: Logical name (OBIS code) of all 200ms secondary values (voltage and current) corrected (channel number = 1). - ZxQ200: Display string of IEC device address added. - ZxQ200: Display unit and scaler for active and reactive meter constants changed (firmware H03 and up). Changes to release 4.3.26 - ZxG300/400: Voltage range separator in production file corrected. Changes to release 4.3.24 - AD-xP/xG: In Home Unit functionality added for firmware T23. - AD-xP/xG: Tree structure partly revised. - AD-xP/xG: Configuration of M-Bus devices modified. - AD-xP/xG: Fixed structure of multi utility profiles added to production file. - AD-xP/xG: Resolution of phase current set to 2 decimal places. - AD-xP/xG: If DST is disabled the deviation is set to 0 (firmware T21 and earlier). - AD-xP/xG: Monthly profile removed for firmware T23. - AD-xP/xG: Channel number in logical name of energy registers changed (firmware T23). - AD-xP/xG: New parameter for impulse constant of ZxF meter introduced. - ZxG300/400: Logical name of pulse output registers corrected. - ZxG300/400: Input of yearly billing period reset on fixed dates corrected. - ZxG300/400: Polarity of power factor monitoring corrected. - ZxG300/400: Billing period average power factor introduced in stored values profile. - ZxD300/400: Support of firmware B30 for pilot series production. - ZxD300/400: 5||1 A now also supported for class 0.2 meters. - ZxD300/400: Minimal start current for direct connected series 2 meters lowered to 10 mA. - ZxD300/400: IEC start current definition modified. - ZxD300/400: Input of yearly billing period reset on fixed dates corrected. - ZxD300/400: Distinction in naming between last average power factor and billing period average power factor in display lists. - ZxD300/400: Naming of total operating time register in display lists corrected. - ZxD300/400: Event 124 (compensation value changed) removed from list of trigger sources for disappearing events. - ZxD300/400: Printout of single profile reset corrected. - ZxQ200: Event status can be added to event log (since firmware H03). - ZxQ200: Inscription of integration/registration period now always possible - ZxQ200: Various settings/rules checked and changed for c.2 configuration. - ZCQ200: Apparent energy and demand registers now also supported for ZCQ200. - ZxQ200: Calculation of number of entries corrected for load profile 2 containing more than 4 entries. - ZxQ200: Input of yearly billing period reset on fixed dates corrected. - all devices: Text for time zone modified Changes to release 4.2.18 - ZxD300/400: Correction of start current for devices with class 0.2, B, C as well as active meters. Changes to release 4.2.16 - Database Browser: The visibility of the fields and the order is user selectable now. Sort by country is possible now. Selection and deletion of more than 20 data sets is correctly working now. Display of secondary voltage corrected for newly stored data sets. - all devices: Limitation of production information to 60 characters. - all devices: In the detail view titles instead of buttons are shown, no navigation possible in detail view anymore. - CU-Q22: Maximum baud rate of channel 1 limited to 9600 bps. - CU-Q22: Handling of pin profile corrected. - CU-Bx: Protocol settings for meters with baud rate switching corrected. - ZFF100: Meters with 3 wire connection only offer measurement mode A anymore. - AD-xP/xG: Delivery state of electricity disconnector selectable now. - AD-xP/xG: The time zone can be negative as well. - AD-xP/xG: Support of firmware T23. - ZxG300/400: Introduction of time zone for clock. - ZxD300/400: Introduction of new current range for ZxD400CT since firmware B24: 5||1 A with maximal current of 10 A. - ZxD300/400: Introduction of user defined start current as in ZxG meters. - ZxD300/400: Suspension hook can be delivered visible or concealed. - ZxD300/400: Introduction of time zone for clock. - ZxQ200: Correction of printout of 'current monitor' and 'period inscription on face plate'. - ZxQ200: Introduction of user defined start threshold of voltage measurement. - ZxQ200: Various corrections in configuration C.7. - ZxQ300/400: Introduction of time zone for clock. Changes to release 4.1.12 - ZxQ200: Trigger sources for alarm and operational indication corrected (firmware H03 only). Changes to release 4.1.10 - Database: Enhanced database browser with filter capabilities, additional country field in all device descriptions. The new browser requires an update of the database (see section 3.2). - all devices: In the register selection of the load profile the registration period average value of the instantaneous values is shown. This only affects the visualisation, up to know the average value has been parameterised already. - CU: In devices with baud rate switching on channel 2 (master with baud rate switching) the dlms transmission rate is set to the same value as the IEC start transmission rate. - CU-Ax: Second channel is set correctly for CU-A5. - CU-Px: Enhanced handling of inactive time windows. - ZxF100: Check the utility serial number if the number of characters match between the format and the start value. - ZxF100: For single rate meters the rate control is set in a way, that rate 1 is always active. - AD-xP/xG: In the clock the time zone information (deviation of local time to UTC) has been added. - ZxG300/400: Introduction of MID accuracy classes for the active part of combi meters. - ZxG300/400: No display of stored values possible if only active rate registers are selected for the operating display. - ZxG300/400: Text of parameter group W76 changed to 'Over Current Monitor Thresholds'. - ZxD300/400: Introduction of MID accuracy classes for the active part of combi meters. - ZxD300/400: Introduction of class 0.2 for meters with integrated interface (ZxD402CR). - ZxD300/400: Introduction of class 0.2 for meters with 3 wire connection and 1 A nominal current. - ZxD300/400: Enhancement of object list for ZxD300/400xR.p1 - ZxQ200: Support of firmware H03. Changes to release 4.0.24 - AD-xG: Maximum number of profile entries is now in line with physical memory size (firmware T22). - AD-xG: Multi utility registers can contain electricity values (firmware T22). - AD-xG: Settings of transparent mode adapted (firmware T21). - ZxG300/400: New security screw for the sealing of the meter cover introduced. - ZxG300/400: Single row terminal block removed. - ZxG300/400: New device types for firmware R03: ZxG310/ZxG400, 120-240 V, 60 Hz, RS232 and RS485 interface. - ZxD300/400: Security group assignment for some registers modified to allow restricted read access also to instantaneous values: Average demand registers have been added to the same group (R70) as the maximum demand registers. The group containing all other registers (R16) has been extended with the following registers: Instantaneous voltages, currents and power, frequency, phase angles and power factors, date of last calibration. This change only affects new device, existing devices can't be changed. - ZxQ200: Starting load 0.02% for meters with 5 A nominal current introduced. Changes to release 4.0.20 - Operating systems: Windows Vista is now supported, Windows NT and Windows 98 have been cancelled. - Setup: New setup program offering better upgrade possibilities for future releases. - Translation: All files now have fixed names but are located in their own subdirectories with the corresponding country code (i.e. 'en' or 'de'). To do a translation, an existing directory must be copied, renamed to the correct country code and all files must be translated. - Database: Connection timeout of DB server enhanced. - Profiles: The order of the profile entries can be modified in all devices. - CU-P3x: Support of firmware D60. - CU-P3x: Various corrections in the handling of the IP address mode. - CU-ADP: For all types without a second channel the adapter settings have been removed. - ZMF100: In case of single tariff meters with firmware M12 all energy registers can be selected for the readout list. - AD-xG: Support of firmware T22. - ZxD100AR: Display lists are now shown correctly in case of stored values without numbering. - ZxG300/400: When switching from F- to M-connection all L2 related items are shown again. - ZxG300/400: Edit field for the power factor threshold monitor corrected. - ZxD300/400: Support of firmware B24 - ZxD300/400: Edit field for the power factor threshold monitor corrected. - ZxQ200: The event log size can be parameterised. - ZxQ200: Energy rate registers can be controlled also via asynchronous signals of the control matrix. Changes to release 3.3.28 - CU: Printout of the configuration enhanced with missing information (i.e. firmware release). - CU: A day change in the time window settings is now accepted without leaving the field. - CU-G3x: Error in the display of the configuration corrected. - ZCF100: Printout of the pulse output constant corrected. - ZxF100: Modification of the maximum possible entries in the display and readout list. - ZxF100: Support of firmware M14 for pre series production. - ZxF100: Display and duration of the test mode after power up corrected. - AD-xP/xG: Support of the most recent firmware releases T01 and T21. - AD-xP/xG: PISTA values for the handling of the phone numbers corrected. - AD-xP/xG: In the PING command quotation marks are now accepted. - AD-xP/xG: Display and selection of trigger sources corrected. - ZxG300/400: Support of firmware release R03. - ZxG300/400: Class 0.5 for wide voltage devices and firmware P03 now supported. - ZxG300/400: RS485 interface for wide voltage devices now supported. - ZxG300/400: Default voltage inscription for wide voltage devices corrected. - ZxG300/400: Start of load profile fixed for all devices with firmware P03 and before. - ZxG300/400: Configuration of security attributes for security level A corrected. - ZxG300/400: Texts concerning calibration coping changed. - ZxD300/400: Handling of error mask corrected for devices with firmware release B23. - ZxD300/400: Default voltage inscription for wide voltage devices corrected. Changes to release 3.3.16 - Setup: Currently selected database remains active. - CU: New, more user friendly selection of the CU configuration. - CU-P3x: Support of firmware D60 for pre series production. - ZxD100AS/AP: Needless column in print out of display lists removed. - ZxD100AS/AP: Manual export of production files possible again. - ZxF100: Terminal protector introduced. - ZxF100: 2 new variants of terminal covers (40mm) introduced. - ZxF100: Maximal current for devices with breaker limited to 80A. - ZxF100: Firmware version added to display lists. - ZxF100: Rated reverse energy registers removed from display lists if the measuring method is set to 'Mode C'. - ZxF100: Support of firmware M13 - ZxF100: Same target directory for *.prd und *.map files. - ZxF100: Number of entries in display lists adapted. - AD-xP/xG: Support of firmware T01 and T21 for pilot series production. - ZxG300/400: Nominal voltage added to display lists. - ZxG300/400: Event 9 (Daylight saving time enabled or disabled) is now triggered in both cases. - ZxG300/400: Correction in the configuration of the electrical interfaces if RS485 and CS are fitted. - ZxG300/400: Correction of the device mask name for the ORACLE database. - ZxG300/400: Support of firmware P04 and ZFG300/400 for pilot series production. - ZxD300/400: Maximal number of entries for the event log corrected if the event status register is captured. - ZxD300/400: Event 9 (Daylight saving time enabled or disabled) is now triggered in both cases. - ZxD300/400: Support of firmware B24 for pre series production. - ZxQ200: Event 9 (Daylight saving time enabled or disabled) is now triggered in both cases. Changes to release 3.2.20 - Setup: Default directory is now 'MAP190_' to avoid unintentional overwriting of former releases. - all devices: Embossing 'SIS025' replaced by 'SCS070'. - ZxF100: Pulse constant for AMR interface introduced. - ZxF100: Serial number always visible. - ZxF100: Adaptation and enhancement 'order specification' folder. - ZxF100: 8.5 mm terminal also possible for meters with 100 A. - ZxF100: ZMF always features a 60 mm terminal cover. - ZxF100: Enhancement of number of entries in display lists. - AD-xP/xG: Support of firmware T01 and T21 for pre series production of Advantis 2.0. - AD-xP/xG: Compressed output data format for profiles now selectable. - AD-xP/xG: Adaptation and enhancement of 'order specification' folder. - AD-xP/xG: Enhancement of owner mark inscription. - ZxD300/300: Change in security system settings for better parameterisation of billing period reset table. - ZxQ200: New configuration of demand measurement: Reactive demand now possible as well as apparent demand. - ZMG300/400: Template for main face plate now exported to production file. - ZMG300/400: Selection and parameterisation of reverse stop in measurement channels corrected. - ZMG300/400: Adaptation and enhancement of 'order specification' folder. Changes to release 3.2.14 - ZxD100AS/AP: Spaces in text fields removed for PISTA export. Changes to release 3.2.12 - Printout: Number of pages corrected in printout. Changes to release 3.2.08 - ID codes: If the rate number is changed all linked ID codes are now updated accordingly. - Printout: Various enhancements in the printout. - CU with RS232: In case of an external modem the communication speed between the CU and the modem can be defined. - CU-P2x: A user name and a password for the login in the GPRS network can be defined. - ZCF100: Various enhancements after pilot series. - ZxF100: Support of breaker and firmware M13 for pilot series. - ZxD100AR: Support of firmware I06. - ZxD300/400: Format of time stamps for R5/R6 commands now also visible in the load profile. - ZxD300/400: Configuration change to ensure the correct setting of 's' or 'S'. - ZxQ200: C.2 now possible with CT/VT correction. - ZxQ200: Text correction for the lower range of the additional power supply:'24 - 125 VAC/DC' instead of '24 - 60 VDC' - ZxQ200: Reactive demand registers removed in case of apparent power. - ZxQ200: Calculation of instantaneous THD adapted. - ZMG300/400: New type with wide voltage range (120/208 .. 240/415 V) available. - ZMG300/400: Instantaneous power can now be selected in the load profile. - ZMG300/400: New PISTA values for the different variants of fraud detection. Changes to release 3.1.12 - ZxF100: Support of firmware M13 for pilot series. - ZCF100: Support of firmware M40 for pilot series. - AD-xP/xG: Correction of modem initialisation for T20. - ZxD300/300: Support of Chinese display. - ZxQ: Resolution of delta registers in test mode is now set to '000.00000'. Changes to release 3.1.08 - all devices: MID accuracy classes A, B, C for active energy meters introduced. - ZxF100: Support of firmware M12. - AD-xP/xG: Support of firmware T00 and T20. - ZxD300/400: Class 0.2 with anti tampering introduced. - ZxD300/400: Special days of TOU are shown again in all cases. - ZxD300/400: Trigger sources of events are stored correctly again. - ZxQ200: Minimum primary current lowered to 20 A. Changes to release 3.0.24 - CU: Support of firmware D51. - ZxD120AP: Scaling of pulse constants for dlms readout corrected. - ZxD100AR: Support of firmware I05. - ZxD100AR: Handling of anti tampering flag corrected. - ZxD300/400: Event 13 can now generate an entry in the event log in case of disappearance. - ZxD300/400: Terminals for additional power supply as well as passwords P1 and W5 now visible in certification feature list. - ZxD300/400: Enhancement of list of errors which can be cleared under the utility seal (B23 only). - ZxQ200: Averaging of instantaneous values (e.g. voltage, current) corrected in the load profile. - ZxQ200: Maximum demand now possible with reactive energy. - ZMG300/400: Support of firmware P03 and R02 Changes to release 3.0.20 - ZxD100AS: Support of firmware F05. - ZMG300/400: Support of firmware P02. - ZxD300/400: Support of firmware B23. - ZxD300/400: Nominal current of 40 A now fully supported. - ZxQ200: Quadrant assignment of measurement channel 20 (EFR) corrected: (QI + QII) - (QIII + QIV). - ZxQ200: Stability check has been introduced. Changes to release 3.0.16 - ZxQ200: Correction of primary data of meters with voltage direct connection. Changes to release 3.0.14 - Device addresses: Length of physical IEC device address enhanced to 30 characters and length of dlms device ID enhanced to 16 characters. - CU: Initialisation strings of modems removed since they are set automatically during production. - CU-Exx: Number of rings in time window adapted. - CU: Object 'auto answer' now visible in CU-Ax with external modem support as well as in CU-Exx. - ZxD300/400: Support of new device type with DC field detection. - ZxD300/400: Protocol and baud rate for interface board 'c7' now selectable. - ZxD300/400: Enhancement of input of billing period table. - ZxD300/400: Display of debounce time of e-contact corrected. - ZxQ200: Calculation and display of iron losses enhanced. - ZxQ200: New type with voltage direct connection introduced. - ZxQ200: Type of PQ-module (RS232 or RS485) is transferred to PISTA. - ZxQ200: Maximum output frequency of transmitting contacts enhanced again. Changes to release 3.0.11 - ID Number 1: Input of complex ID's with checksum (e.g. EAN-Code) now supported. - ZxD300/400: No correction of load profile memory size for devices without load profile. Changes to release 3.0.08 - ZxD300/400: Size of load profile memory reduced by 1 page (B21 und B22). - ZxD300/400: Printout of profiles enhanced with number of entries. - ZxD300/400: Printout of the number of entries of the profiles added. - ZxQ200: New calculation method for apparent energy (ignore leading reactive) - ZxQ200: Energy delta values over billing period now available. - ZxQ200: Stored values can be shown in operating display. - ZxQ200: Stored values profile available for c.4 and c.6. - ZxQ200: Changes in calculation of loss resistors and pulse constants in case of three wire connection. - ZxQ200: Iron resistors now have a resolution of 2 decimal places. - ZxQ200: Parameterisation of meter constant U2 for voltages between 120 and 190 V added. - ZxQ200: Additional display of meter constants for losses based on effective resistors. - ZxQ200: THD OBIS codes now can be used for display. - ZxQ200: Maximum frequency of pulse outputs enhanced to 24 Hz. - ZxQ200: PQ module for class 0.5 added - ZxQ200: Base of THD percentage values changed to secondary values. Changes to release 2.5.16 - PISTA: Interface modified to support DD-ID's larger than 32768. - ZxD100AR: Support of firmware I04. - ZxD100AR: Configuration with 1 input and 1 output: Correction of signal assignment of the static output. Changes to release 2.5.14 - CU: Conversion of old data models now possible without loss of data (L&G Dialog CT => ZxDATCT B13B13 => Param21) - CU: Wrong OBIS code of the association object has been corrected. - CU: Terminal inscription and device type corrected (M20 und Q22). - ZxD100AS/AP: Parameterisation of measurement system corrected for devices with reverse stop. - ZxD300/400: Designation and terminal inscription of extension board '046x' has been corrected. - ZxD300/400: Support of new extension board '0450' with 4 outputs and additional power supply. - ZxD300/400: OBIS code for gas and water of external pulse inputs corrected. - ZxQ200: Support of ZPQ meters. - ZxQ200: DIP table is disabled in all meters with a frequency of 16 2/3 Hz. - ZxQ200: Support of external PQ module. - ZxQ200: Dlms response time for all integrated interfaces is now set to 0 ms. - ZxQ200: Register resolution for secondary data meters adapted. - ZxQ200: Lower limit of primary current changed to 50 A. - ZxQ200: No load limit of ZFQ meters corrected. - ZxQ200: Delay time of current monitoring can now be parameterised and is not fixed anymore to 10 s. - ZxQ200: Accuracy class 0.5/0.5 removed (not in portfolio). Changes to release 2.5.10 - Database: List of most recently used databases removed. Complete list available after pressing the 'Select' button. - Control table: Printout of outputs adapted to display: immediate change = '<- --' , changes synchronous to end of period = '<- \-' - Profiles: In all profiles the OBIS logical name instead of the display code is shown for the captured objects. - ZxD100AR: Support of new software I03. - ZxD300/400: The size of the hdlc transmission buffer can be selected for all interfaces now (as in CU). - ZxD300/400: In conjunction with scaling factors also decimal places are available. It is now possible to parameterise delta registers with the precision required. - ZxD300/400: Indirect synchronisation of the clock via output of the control table is now working correctly. - ZxD300/400: Event status register again selectable for event log. - ZxD300/400: Support of new type: ZxD402 with 60 Hz. - ZXD300/400: Support of new extension board '0460' with 4 outputs and external DC power supply. - ZxQ200: The size of the hdlc transmission buffer can be selected for all interfaces now (as in CU). - ZxQ200: For measured quantities +R and -R the quadrants have been added for printout. - ZxQ200: Transmitting contact test mode has been removed for devices with software H90. - ZxQ200: Input fields for description of additional power supply and rate control have been corrected. - ZxQ200: Duplicate entry for the additional power supply voltage has been removed. - ZxQ200: In the list of losses also the contents of the variable registers ME23 and ME24 can be added for c.6. - ZxQ200: Units for pulse constants adapted according to COSEM definition. - CU: Type designation Q2 changed to Q22. - CU: GSM modem type only shown for G2x and P2x types. - CU: Object Auto Dial removed for D45. - CU: In all time windows the yearly repetition has been removed since this is not supported by the devices. - CU: Terminal inscription for E21 und E22 corrected. Changes to release 2.4.04 - Licensing: Start up error due to licensing problems fixed. - ZxQ200: Firmware H02 and H90 activated for all licenses. - ZxQ200: Inactive profiles contain at least one entry in the captured object list to ensure later reparameterisation. - CU: In all E2x modules the alive interval in case of fixed IP addresses is activated automatically. - CU: For all Q22 modules H02 dlms addresses have been modified. Changes to release 2.4.02 - Licensing: The license key is invisible after input (copy protection). - Time of use: Data exchange via clipboard (copy and paste) between different data sets as well as between different devices is now possible. When adding exception days the day table number can be entered directly. - ZxD100AR: Selection of M-Bus slave type again available. - ZxD300/400: Extension of alert trigger sources: Over current (4) and control input signal change now supported. - ZxD300/400: Interface board 'c7' for Chinese applications now supported. - ZxD300/400: Type designation of the RS422 interface board changed from 'c4' to 'c6'. - ZxD300/400: Number of exception days enhanced from 50 to 100 (B21 and up). - ZxD300/400: Threshold of neutral current monitor is kept after editing. - ZxD300/400: Display and selection of the integration period control via external inputs has been corrected. - ZxD300/400: Display and selection of ID number codes has been corrected. - ZxD300/400: Stored values of operating time registers are shown with index in display lists. - ZxD300/400: Length of IEC identification string has been reduced to 16 characters (according to standard) instead of 20. _ ZxD300/400: Display of control matrix of former devices with firmware B12 to B14 has been corrected. - ZxD300/400: When entering codes to the IEC-Readout list they are displayed the same way as they are given out by the device. - CU: For all P2x types with firmware D50 a user name and a password for the PPP protocol can be entered. - CU: Support of type Q22 with firmware D90. - CU: Designation of terminals for G4 and G5 again available. - ZxQ200: Support of firmware H02 and H90. - ZxQ200: Quadrant assignment for reactive energy (+R, -R) now selectable as in ZxD300/400. - ZxQ200: Devices with 5A nominal current now support a maximal current of 200%. - ZxQ200: Enhancement of output pulse constant range. - ZxQ200: Enhancement of security system for operation with CU Q22. - ZxQ200: Correction of LED pulses for U2 and I2, correction of pulse constant RI2. - Data export: Creation of production files supported for all devices in HQ menu. Changes to release 2.3.04 - Licensing: The license is not hardware related anymore, i.e. you can install as many copies of the software within your organisation. To do so, new licenses are required. Please follow the instructions in paragraph 3. - all devices: ID numbers visible only once in the tree (ID numbers for field parameterisation have been removed) - CU: Support of new CU types G2x, E2x, M2x and P2x with software D45 and D50. - ZxD100AR: Scaling of the impulse values of the transmitting contacts is now printed correctly. - ZxD100AR: Hdlc address is now transferred correctly to the PISTA database. - ZxD100AR: Start baud rate of the electrical interface in case of automatic detection is set correctly. - ZxD300/400: Support of firmware version B22 in all licenses. - ZxD300/400: Class 0.2S for series 2 devices since B22 again available. - ZxD300/400: The delay time of the current monitor is now printed correctly. - ZxD300/400: Variant without control inputs has been removed since it is not in the portfolio. - ZxD300/400: Designation of the RS422 connector has been fixed. - ZxD300/400: Event 13 (change of the state of a control input) has been introduced to the event log for B21 and up. - ZxD300/400: Energy register 23 and 24 are only fixed if the minimum power factor is used. - ZxD300/400: Instantaneous active and reactive power have been introduced for B21 and up. - ZxD300/400: Various face plate inscriptions have been corrected. - ZxD300/400: Scaling of the impulse values of the transmitting contacts is now printed correctly. - ZxD300/400: Inscription of instantaneous voltage L3 and the code for under voltage registers have been corrected in all display lists. - ZxD300/400: Status word is not fixed in the event log anymore, only timestamp is mandatory. - ZxD300/400: Security system: Trigger for alerts is now assigned to group W29 instead of W82. - ZxD300/400: Codes in the display lists are printed the same way as they are shown by the device (with or without value group B). - ZxQ200: Voltage inscription for rate control inputs fixed ('without' added again). - ZxQ200: Maximum number of entries in the display lists adapted. - ZxQ200: Synchronisation input also available for devices without rate control inputs. - ZxQ200: Maximum frequency of the transmitting contacts has been enhanced to 6 Hz. - Time of use: The position of the crosses in the printout of the day tables has been fixed. - Import: Various problems in the import and the 'Save as' function have been fixed. - Reparameterisation: Firmware release is checked again. - Printout: Device type in the footer is now shown correctly. 3. System Requirements ---------------------- - Supported operating systems: Windows 8, Windows 7, Windows Vista, Windows Server 2003, Windows XP - The following system components which are not part of Landis+Gyr MAP190 must be installed on your computer: - Microsoft Access Database Engine 2010, especially Microsoft Access ODBC Driver version 14 (ACEODBC32.dll). - Additional ODBC drivers depending on the database in use. 4. First Time Installation -------------------------- In order to install correctly Landis+Gyr MAP190, a) ensure that you have administrator privileges on your PC b) run 'setup.exe' c) follow the instructions of the setup wizard 5. Upgrade ---------- 5.1 Upgrade of a former Landis+Gyr MAP190 release 5.9 to the most recent release 5.9 The newest release 5.9 automatically replaces any former release 5.9. All data including the license is kept. Procedure: Start the installation procedure (run setup.exe) and confirm the upgrade. 5.2 Upgrade of Landis+Gyr MAP190 5.8, 5.7, 5.6, 5.4, 5.3, 5.2, 5.1, 5.0, 4.x, 3.x, 2.5, 2.4 or 2.3 to the most recent release The new release can be installed in parallel to a former release 2.3 and up. In this case a dedicated installation directory is required. It is strongly recommended to uninstall the old release because it will no longer be supported. All data including the license is kept. Since release 5.6 the old Microsoft JET database engine is not supported anymore. It has been replaced by the Microsoft Access Database Engine (ADE). If necessary please install the Microsoft Access Database Engine 2010. All existing MS Access database (*.mdb) can be further used. You need to create a new data source (DSN) in the ODBC database manager using the 'ACEODBC32.dll' driver. The new browser (since release 4.1) requires an update of all existing databases. The conversion is done automatically after you have confirmed the update. The converted databases can't be accessed with a former MAP190 release anymore. To avoid unwanted loss of data it is strongly recommended to make backups of any local database before conversion (just copy the *.mdb files to a different location). These backups then still can be accessed with a former release if the conversion fails or in case of later inconsistencies. Procedure: 1. Uninstall the old release. 2. Start the installation procedure of the new release (run setup.exe). 3. In case of a parallel installation select a different directory. 5.3 Upgrade of Landis+Gyr MAP190 prior to release 2.3 Former releases are not supported anymore, an upgrade isn't possible. 6. Supported Devices -------------------- - ZxF100 series 1 with firmware releases M14, M13 and M12 - ZCF100 series 1 with firmware release M40 - ZMD120AM with firmware releases A04 and A03 - ZxD100AS/AP with firmware releases F05, F03, G03, G02 and G01 - ZxD100AR with firmware releases I06, I05, I04, I03, I02 and I01 - ZxG300/400 with firmware releases P07, P06, P50*, P05, P04, P03, P02 and P01 as well as R06, R05, R03, R02 and R01 - ZxD100/200AT with firmware releases C09, C08, C07 and C06 - ZxD300/400 with firmware releases B32, B31, B30, B24, B23, B21, B20, B14, B11, B10, B09 and B08 - ZxQ200 with firmware releases H04, H03, H02, H01, H00 and H90 - Communication units Ax/Bx/Mx/Gx/Dx/Ex/Px with firmware releases D72, D71, D60, D51, D50, D45, D44, D43, D42 and D41 - Communication unit Zx - Communication unit Q22 with firmware releases D91 and D90 - Communication module AD-xP with firmware releases T05, T04, T01 and T00 - Communication module AD-xG with firmware releases T25, T24, T23, T22, T21 and T20 The following devices are explicitly not supported: - Communication units Ax/Bx/Mx with firmware release D40 * = device not released in MAP190 or device not yet released at all 7. Known Restrictions --------------------- - It is not possible to import data from Landis+Gyr MAP120. 8. Languages ------------ Installation: English and German Tool: English and German Help about ZxQ200 devices: English and German Help about ZxD300/400 devices: English and German Help about ZxG300/400 devices: English and German Help about ZxD100AR devices: English and German Help about AD-xG/xP communication modules: English and German Tool help and user manual: not available 9. Data Files and Database -------------------------- An empty database is included in the package. All necessary data files to order a device can be obtained from your local Landis+Gyr representative. 10. Licensing ------------- The software is not protected against copying, everybody is allowed to install a demo release with limited functionality. To obtain a valid license please contact your local Landis+Gyr representative. 11. Support ----------- In case of questions on MAP tools or Landis+Gyr meters please contact your local Landis+Gyr representative. http://www.landisgyr.com